Campaign Style chest. Part 1

One thing about building Campaign Style chests is you gotta love the dovetail. Alot.

Hogged out the majority with an electric router.

The dovetails were easily the most intimidating part of the carcass build, so I wanted to practice before I started on the project. I had some scrap pieces of beech that I thicknessed to be the same as the chest would be. I found an excellent tutorial for full blind and secret mitre dovetails at

There are so very many videos and blogs that show and/or describe how to make standard through and half blind dovetails, but there are surprisingly few that show how to make full blind and secret mitred dovetails. Even so, I did find several to choose from and always came back to the mikes-woodwork site. His instruction really worked for me and I used it for all subsequent dovetails for the project.

The reason I was looking into the full blind and secret mitred dovetails is that they were used in period pieces, mostly for the top corners. I checked some pieces locally and found that some had half blind and some had full blind, but I haven’t found a secret mitred carcass yet.

And just a warning. I’ll use “half blind” and “half lap” dovetails interchangeably so if you see me change from one to the other in mid-thought I’m still talking about the same thing.

Laying out my lines.
The three pieces with the rebate.
Cut your pins first. It is easier to transfer the pins to the tails with this kind of joint.

Several years ago when I was just beginning to play with joinery, I learned to cut pins first. Not because I watched Frank Klaus or anything like that, but because I found it to be much easier to transfer the pins to the tails. At the time I thought I was cheating or doing it wrong, so I then learned to cut tails first. Since the question, Pins or tails first, has become such a volatile debate, I don’t usually say which way I think is best. That said, I haven’t made enough dovetail joints to even be considered a beginner.

With full blind dovetails you don’t have to worry as much about the proportions of your tails to pins, so make them both big.

I used a mitre jig to reference my chisel from the top and bottom.
And for my first try it wasn’t too bad. Surprisingly little cursing and hardly any crying at all!

Even though my trial run on the hidden mitred dovetail went OK, I decided not to use them in the project. Instead, the two top corners are full blind dovetails (without the mitre). I didn’t take pictures of that procedure but will do so for my next Campaign piece. I did take a picture of the pins though.

Some of my scribbling.

For the backs of these pieces (Chests and Secretaire) the norm was to use a simple boarded back that was screwed into the rebates in the carcass. Another method was a frame and panel. I chose a modified version of the frame and panel for mine. I used mostly offcuts for the frame and panel, but for the frame I needed non-spalted straight grain.

Frame and panel back for Campaign style chests.
My frame and panel back.

The back frame is 12mm thick (about 1/2 inch). I used a half lap here since I didn’t want to fiddle with mortise and tenon that small. The panel is slightly thinner and goes into a 5mm groove in the frame.

Web frame (webbing) for between the drawers.

I had some leftover bookmatched flame beech but it wasn’t long enough to use for the backs, so they ended up in the webbing between the drawers. The web frame is the same thickness as the carcass or 18mm (about 3/4 inch). For this, I used mortise and tenon.

While searching for scrap beech I could use for the frames, I came across some oak that was the right length and thickness, so I laminated a piece of flame beech on the front and called it a day.

And I have a couple of boxes. Getting ready to build the drawers and gallery next.

The flame is beautiful, but I was not careful with this and damaged the soft wood on the left side.

To be continued…

Campaign Style Furniture design, part 1: brass hardware, straps and corner mounts.

Campaign furniture spanned more than 200 years of English furniture periods from the Georgian through to the mid 20th century. Even though it was around for so long the campaign-style did not change much in those 200 years, which could be attributed to a couple of factors. First, since the furniture had to be mobile and sturdy for use on or near battlefields there are arguably a limited number of ways to build that furniture. Second, the clientele were military officers to begin with, who tended to be staid, conventional, and reserved in their tastes and styles.

I believe the first campaign furniture was made for British naval officers in the early Georgian period (the early 1700s). I’ve perused the Christopher Clarke Antiques Blog and Christopher Schwarz’s book and haven’t found anything definitive on this and will probably follow up with more posts on the history itself.

One feature of campaign furniture that tends to stand out (and is used heavily in contemporary interpretations) are brass coloured straps and hardware.

Brass coloured straps are a decorative element in modern furniture. You will likely find that on modern pieces the straps, corner mounts and related parts are not recessed and installed flush, but are proud of the surface. Another difference is that the straps and hardware will likely be fixed with tacks, pins, or small nails. You may also find the pieces glued to the carcass.

The utilitarian and mobile nature of Campaign furniture means that the brass hardware is functional as well as decorative. Brass straps and corner mounts protect edges and corners. Straps may also help to keep sides from bowing or flexing and creating gaps.

A corner mount.

Corner mounts will usually be flush with the wood, which requires time and effort and would be difficult to automate. The screws will be countersunk slotted screws and again flush so as not to catch on anything while moving it.

Brass straps.

The brass straps are also mounted flush and protect the edges and possibly keep the sides from bowing or flexing since they are of solid wood (mahogany, teak, or in this case, oak).

For part 2 I’ll talk about the drawer hardware.

18th Century Italian chest restoration.

One of the most valuable (to me) skills that my furniture making course has taught me is the core fundamentals of furniture restoration and repair. Graham and Clare, who are both as great at teaching as they are at repair and restoration, have allowed me to look over their shoulders (and incessantly ask questions) as they have worked on pieces. I have also been able to work on some of them myself, which has not only been a great and challenging experience but has been extremely fun as well.

Graham and Clare have both been with the Chippendale International School of Furniture for more than 2 decades and are easy to talk to and wonderful to work with on these great pieces of furniture.

Recently, an Italian chest, much like this one I wrote about previously came into the school for some work.

The goal was to fill/replace the missing pieces and to make the repairs sympathetic to the age and blend them into the overall condition of the piece. If we decided to make the repairs perfectly flat and shiny with no gaps, then each repair would have stood out and looked out of place.

First thing was to lightly clean the areas that needed repair.

Each of these spaces was cleaned with scalpels, awls, and pretty much anything I could get my hands on that was small enough to get into the crevices and cracks. The bottoms of these spaces needed to be relatively smooth so when I fit the replacement pieces of wood in there they would sit flat and have a good stable glue surface.

More of the missing pieces.

The next step was to put tape over each of the empty spaces and lightly shade with a pencil to get the outline of the missing area.

After I had a good tracing of a missing piece, I put the tape on a piece of (in this case) walnut that I’d be using to patch with. I made sure to orient the grain with the existing veneer.

Anselm and Graham believe the table is from around 1760 and the veneer is several times thicker than any you can buy today, so the repair pieces were resawn on a bandsaw to be just a bit thicker than the old veneer. This way we could pare down the patches to the correct level.

Next, I cut out the pieces oversized and then fit them using small files, sandpaper, and scalpels.

This shows a couple of different stages. A couple of the spaces have been cleaned, one is ready to be traced, and one has a patch already fit (it still has tape on it).
Another area ready for patching.
And with some of the patches fit.

The next stages were to glue the pieces into their respective spots

Using a combination of tools to shave the patch down a bit.

Once the patches were in and the glue dried, I used a combination of water dies to get the patches to blend with the background. I then used coloured wax sticks and melted a mix of colours to fill and blend the repairs. (I don’t have pictures of these steps because once I got into it I was so engrossed that I forgot). Next was a light going over with some black wax, to blend all of the repairs with the rest of the table top.

As always, the repair and restoration is just a wonderful experience.

A closer look at the 18th-century Italian chest.

In the previous post, I was working on the top of the chest but didn’t show any of the rest of the piece, so here goes.

The first thing I noticed when the piece came into the shop was the back.

It initially looked, and felt, like thin cement covering the joints but Graham identified it as gesso. This makes more sense because workshops would have had gesso available for painting (and gilding?)

This next picture made me think that most of the carcass may have had a gesso coating. The drawer side looks like it could have been covered, and then through the years the majority just wore away.

But then the inside of the drawer again looks like the gesso was used to cover gaps in joints, smooth dents, and fill holes. So I don’t think the gesso was used to cover the entire carcass, but I do believe it was added at a later date to cover gaps that developed as the lumber dried and shrank.

Next, I looked at the drawers. This along with the back of the chest brings up an interesting point. The craftsperson (craftspeople) who worked on this were very efficient with their time and energy. Non-show surfaces were not smoothed or scraped.

And, unfortunately, this piece had been a meal or two for some woodworms. Unfinished surfaces were given woodworm treatment as soon as the piece came into the shop.

This next picture highlights a couple of points. First, I think it re-enforces the idea that the gesso was a later addition to cover up the gaps made by dried and shrunken wood. Second, the non-show surfaces again show the efficient use of their time. The only smooth surface in this drawer space is the bottom where the drawer sanded it smooth from hundreds of years of use.

I eventually started looking at the show surfaces.

This marquetry is very similar to the table that came in a while back.

A portion of the Italian table that came in for restoration a while back. I’ll post more on this one later.

One thing about the marquetry is that the lines for the detail are not carved like first thought. They are drawn.

I didn’t think much of this at first, but when Graham needed to do some work on the table he discussed how important this detail is. If you have to use meths (methylated spirits – denatured alcohol) to clean or take off the finish for any portion, it can also erase the detail work so you have to be careful where and how you use any chemicals to clean a piece.

One major difference between the table and the chest is that the table is all marquetry and veneer with a clear finish, whereas the chest is marquetry and a painted veneer.

Painted veneer.
Veneer with clear finish.

Graham thinks this means the two pieces were made in the same shop, but the chest was a project for an apprentice. That makes sense to me and I’m running with that theory.

Arts and Crafts style mirror with gilding.

One project that really took me by surprise while at the Chippendale school was a mirror that ended up requiring more brand new skills than I would have thought possible.

I already knew that I wanted to do letter carving and I knew which quote I would use. I first saw the quote “The lyf so short, the craft so long to lerne.” in a picture of a fireplace mantel in a craftsman style home of Gustav Stickley, who was one of the first, and most well known, US mission (arts and crafts) style furniture makers. I then did some research to find out that it is from a poem by Chaucer, called “Parliament of Fowls” which is about how love and life are crafts that take a lifetime to learn. It is also thought to be the origin of St. Valentine’s Day. That said, I only knew it as a quote about traditional crafts and still think of it that way.

It started out as a simple drawing. At this point, I was so focused on my other project that I didn’t put a lot of thought into the scale or proportion, but I knew I wanted an arts and crafts style mirror.

This plan lasted long enough to start dimensioning the lumber and then went through several modifications (in my head). Then, when we ordered the glass I realized I had designed the frame too large, so it went through another major modification.

I thunk and thunk and then thunk some more over the resizing and what shape the mirror should take but had already started laying out the letters since the letter size and font would tell me generally what shape the mirror would take. I knew from the beginning exactly which font I wanted to use on this as I’d seen it used quite often for arts and crafts lettering, but I just didn’t know what it was called. I searched several font websites and found it on and also on

This is a public domain font and is free for all kinds of usage.

Dyer Arts and Crafts font.

I didn’t want the letters too small as that would make the carving more difficult so when I settled on a size I printed them out, cut and spliced them into their lengths and lay them out on the lumber. Here I needed to make sure my kerning was consistent because I was splicing groups of letters together.

I was worried that as I started to outline the letters onto the wood with the gouges that the letters would move and I’d lose my place, so I also used graphite paper (carbon paper) to trace the outside lines of the letters. This turned out to be overkill and actually created more work for me because I then had to remove the tracing afterwards, which turned out to be more difficult and fiddly than I had planned.

You can see the result of the tracing paper in a few of the letters.

The letter carving itself was very enjoyable and cathartic. I would be so engrossed in my carving that hours would fly by and I’d have to force myself to take a break, stretch, grab a cuppa, chat with the other students, and then dive right back in.

Once I’d reached a point that my rough out of the letters was finished, I shellacked the letters. This was to exaggerate the roughness and show me where I needed to concentrate my efforts to smooth the sides and the outlines.

I’d shellacked the top row, but not the bottom yet.

The roughing out of the letters was the quick part. I spent more than twice as much time smoothing the sides and edges.

After the rough out of the letters. Next I’m on to the smoothing.
Getting there.

Once I’d finished the smoothing of the letters, I was ready to stain and then gild. I later found out that this was the wrong order and next time I’ll gild and then stain. The reason being that when I finished gilding I had to sand the surface in order to create the crisp edges, but doing that removed most of the stain. I then had to restain after I had finished sanding. Not a huge issue as the restain cost me a part of a day and I had to let it dry overnight before shellacking.

I also had to regild the letters as I initially didn’t follow the tutor’s instructions correctly. Richard Walker at was the visiting tutor for our gilding instruction and was great to work with. He never cracked a joke and we always knew when he was being serious. 😉 After realizing my mistake and regilding the letters, I sanded then restained using my super secret mix of water dyes.

Some of the testing I did for the mirror frame. Not all, but some.

After letting the stain dry overnight, I shellacked the front side. This was so I could finish staining the edges without it bleeding into the front.

As I was doing all of this I also worked on the side pieces and created the mount in the back to hold the glass. I don’t have pictures of that, but may add some at a later date.

I also didn’t take pictures of the glass/water gilding on the glass, and I’m really kicking myself now. That process was incredibly interesting and I can’t wait to do another project like this. Again, Richard was excellent to learn from as he was able to walk me through the process several times (I kept getting sidetracked on other stuff and would come back and say, “uh, I can’t remember what you said to do here”). Very patient and a great teacher.

First, I laid out the background, which was white gold (I think it has an Italian name, but can’t remember). Then, I scratched out the outline of the roses. For each rose I started with red gold, then added white gold to the center. I then scratched out the leaves and used green gold. I finished by scratching out the stems and then painted over the back with black acrylic paints. I’ve really condensed the process here because I don’t have a photographic record of the steps, but even though there are a lot of steps here and I had to wait overnight for the water to dry before I could move on to the next portion, it went surprisingly quickly. I will post pictures of the process when I do my next glass gilding project.

And the finished product, with 7 coats of shellac. I’ll add more pictures later.

Late 19th C Empire Style Rocker Restoration Part 1

One of the first projects I’ve started working on since moving back to the US is a rocker I picked up at an antique shop. Normally, you don’t find a piece in this shape in an antique store, but it looked like someone wanted to have a go at it and then gave up. The caning had been removed and some of the paint (original dark red) had been removed, but other than that it was just in a sorry state.

Someone got started on this project but didn’t have the time or desire to finish it.
A previous repair.

As I went over this piece, I noticed some things that I would change when I rebuilt it. An example is the rockers, which split along the grain in several places. I’ve decided not to try to reuse these rockers, as I did some experimenting with glue-ups and looked at all the holes created by other repairs and figured it wasn’t worth it.

Another thing I decided to change is how the seat was put together. There were two dowels holding the sides to the front and back pieces of the seat. The side pieces were curved and they split in the short grain.

These side pieces of the seat split along the short grain at the edge.
A bit blurry, but you can see where it split through both dowel holes and then up through the top.

Other than that I didn’t see much that I wanted to change so I took the chair apart.

Once I had the chair apart (except for the top rail and the side piece that I think had been glued together with epoxy or similar) I stripped and cleaned the pieces so I could better evaluate each piece and the joinery.

This is when I found that the frame for the back caning had split into dozens of small pieces, so this will need to be replaced.

Next up in part 2 I make parts for a new seat frame.

Chair caning project.

A few months ago, my wife and I picked up a couple of chairs that we wanted to work on. Both had caned seats and one (the Empire style rocker here ) also has a caned back.

Two projects we picked up several months ago.
Caning before removal.

I’d been reading about seat caning for a while and have been following Ed Hammond and The Wicker Woman on YouTube. The book I got was “The Craft of Chair Seat Weaving, with Cane, Rush, Splint, and Rope” by George Sterns. The book is a very good starter and I referred to it quite often for the basics. The YouTube videos are much better for the details and to better be able to adjust for the curves and other fiddly stuff. I also used Ed Hammond and The Wicker Woman as guides for the “no knot” method for the underside.

To start out, I stripped the chair and then prepped it for a new paint job. I went with milk paint and initially tried what I thought was Barn Red, but turned out to be closer to Hot Pink. Rather than remove this and start over I just painted Pitch Black over it. I did not want to distress this, but I figure that it will distress naturally very nicely with the red/pink underneath.

I stripped the chair and then had a good look at the joints to make sure everything was solid. The chair was in great shape so I didn’t need to redo any joints.
Not the colour I was looking for.
Much better! A few coats of Pitch Black and then a few coats of wax later and it’s ready for caning.

I had several false starts on the caning portion. As I got past the verticals and into the horizontals I had to unweave several sections and start over. It took quite a bit of thinking, doing, undoing, thinking, doing, undoing before I got the verticals and horizontals that I thought would work.

This was attempt 3 or 4. Can’t be sure.

Once I got into the diagonals I realized that there were still issues with spacing in the horizontals and verticals. I had to figure out how to either work around some of these obstacles or redo them. I ended up doing both.

I will probably redo this seat in the future, but once I get the border finished it will reside in our kitchen for a while.

Still need to add the border around the sides and front. This has been a huge learning experience, but I do feel better about getting started on the Empire Style Rocker, once my repairs are finished on that one.

Update 26 July 2020: I finally finished the last of the border and cleaned up the underside.

I ended up doing more of a hybrid ‘no knot’ with a couple of knots due to being unable to plan ahead or stage my cane ends well enough. I surprised myself with how strong these cane seats are: I’ve already sat in this chair a few times and I’m a rather large person.

I have a couple more caning projects coming up am ready to improve on this one.